Direct download of this episode: Episode 430
Great episode as usual; thank you. Also, much thanks to John for his segment on SSD solutions. Three years ago I tried to upgrade a PDQ Powerbook with an OWC SSD drive and encountered the master/slave issue that prevented the SSD drive from working. The OWC's drive is set to master state (unchangeable) which conflicted with the CD drive which is also set to the master setting on these Powerbooks. Thankfully the drive worked beautifully in another Mac I owned, but I never knew how to solve the issue until you aired this segment. The card(s) with switchable settings is just what I need. Thank you so much for shedding light on this issue to an otherwise fine Powerbook. Looking forward to the next episode.
Just a thought: Has processing power on the Mac's progressed enough that Apple (or some other developer) could produce one application (emulator) that would emulate all Mac OS systems (1.0 - 10.11)? This would produce a way for old applications to be run and files accessed yet produce a reason for Apple to get old users to upgrade. I'm not trying to take the romance out of retro but I can see one good Pro Mac (w/ emulator add-on board?) with this ability being a boon for commercial companies with old Mac application & files and some retro users.
Is it at all viable to use SSDs in older Macs? No PPC Mac supports TRIM (which was introduced with 10.6.), wouldn't you run into problems sooner or later? Any experiences?
I was hoping some more experienced SSD users would answer your post and maybe they will. I believe, I have read in the past it was a problem, but there has been a lot of open source software developed to minimize this issue. See the next episode for more info, and keep your eyes on Low End Mac for that diagram that Rick is going to design showing SSD upgrade paths/options for certain Macs. Back in 2014, when I was looking into upgrading systems (G3 & G4), I sidestepped the TRIM issue by going with OWC's line of SSD's for older systems (Mercury Pro Legacy & others). Apparently, these drives have built in drive leveling, etc. See here: https://eshop.macsales.com/shop/ssd/owc
I installed mine in December 2014 and have had no issues with the drive (boots G4 in 45 seconds).
Hopefully, someone with SD card upgrades will post to answer your question also. They usually have to deal with the TRIM issue you are speaking of.
Best Regards - Jake
Thanks guys. I ordered the Ableconn adapter and am going to install it with a high quality 120 GB mSATA SSD in my G4 PowerBook 1.67 GHz. This is my workhorse Mac (still no Intel Macs in the house). Its original HD has given up the ghost after >10 years. I'm booted from an external FW drive right now but would like to have the portability of a built-in drive again. So I guess this is the best time to try and see how it goes.
Thanks Rick! The Ableconn adapter finally arrived. They don't sell them in the UK/Europe and don't ship to Europe at all, I had to ship it to my US address and then forward it.
Which jumper setting should I use? Master or Cable Select mode? (Surely nor slave mode?) The adapter is preconfigured to Cable select, and I'd like to make sure I set it right before installing. I don't want to risk firing up the G4 PowerBook while it's disassembled.
Also, I'm going to go with a Samsung EVO 250 GB mSATA instead (my PowerBook should support it) since they're actually about 30€ cheaper right now than the 120 GB ones.
I installed the mSATA SSD inside the AbleConn adapter today, leaving the jumper at Cable Select. The 17" PowerBook is a pleasure to work with as it's really spaceous inside, all screws and no glue.
Everthing worked smoothly, the SSD was recognized immediately, formatting as HFS+ and then cloning my boot drive to it was no problem. Had Mac OS X rebuild system cashes and verify the file structure for good measure. I'm booted into the SSD as I'm typing this. Applications start a lot faster. I don't know how reliable it'll be in the long run, but it's looking very good right now.